Easy to Operate Brown Gas Generator Machine System

Product Details

Easy to operate Brown gas generator Machine System

SPECIFICATION

Mode

Specification

GTHO-6500

Input Voltage

380 ±10%,50/60Hz,three phases

Rated Capacity (KVA)

22

Working Gas Pressure (Mpa)

≤0.2

Relative Humidity (%)

90

Rated Gas Production (L/h)

6500 ±10%

Water Consumption (L/h)

3.8

Maximum Cutting Thickness (mm)

200

Effective Punching Thickness (mm)

70

Water Feed

auto

Cooling Mode

Air Cool

The Insulation Level

F

Power Supply Protection Grade

IP21S

Flame Temperature (℃)

Adjustable 800~3200

Working Medium

Filtered water or deionized water or soft water

Working Method

Continuous

Enviroment Temperature (℃)

0~40

Outline Dimensions - L*W*H (mm)

1300*930*1820

Gross Weight (kg)

520

Ventilation Space Requirement (mm)

400 in each direction

 

公司介绍GIF图.gif

▲Enterprise Show


Welding and Cutting integrated Machine


Hydrogen and oxygen welding machine maintenance matters:

1. Regularly purge the dust with compressed air, and wipe the parts inside the machine with a dry rag to keep it clean.

2. Pay attention to adding water in a timely manner and do not dry it. Before adding water, turn off the machine, shut down the machine, and release the remaining air.

3. When the machine is not used for more than 10 minutes, it should be turned off, turned off, and let off the remaining air.

4. When the electrolyte becomes dirty, the electrolytic cell should be cleaned in time, and the liquid is mixed again in a weight ratio of 1:4 (ie, 1 part of potassium hydroxide, 4 parts of water).

5. For other precautions, refer to the manufacturer's instruction manual.


证书介绍.gif

▲Honor certificate


Hydrogen and oxygen welding machine application field:

Small Hydrogen Oxygen Welding Machine Suitable for Jewelry Welding, Jewelry Casting and Die Casting, Frame Welding, Thermocouple Bimetal Wire Welding, Motor Enamel Welding, Tooth Patch Repair; Plexiglass Polishing, Acrylic Polishing, Fish Hook Welding, Quartz Glass Pipe drawing seal, quartz glass tube heating, IC chip packaging, optical fiber welding, tungsten wire burning, tungsten wire burning, non-ferrous metal welding and so on.

Medium and large-scale hydrogen-oxygen welding machines are commonly used for brazing of large metal workpieces, flame processing of large quartz glass tubes, flame processing of large-scale quartz glass rods, flame cutting of carbon steel, flame cutting of continuous casting billets, and sealing of ampoules for pharmaceutical plants. Incineration and other wastes.


车间打包.gif

▲Machine packaging


Hydrogen and oxygen welding machine advantages:

1.Energy saving

50% energy saving than traditional welding

2. Environmental protection

The fuel needed for hydrogen-oxygen welding comes from water, which generates water after combustion, without any pollution to the environment.

3. Security

The gas required for hydrogen-oxygen welding is produced side by side. It is not produced when it is not used, that is, it is manufactured on-demand, how much is produced, and there is no stored gas, thus avoiding the risk of explosion of the high-pressure cylinder.

The Hydrogen Oxygen Welding Machine incorporates multiple safety anti-tempering devices. Even if the user misoperates, because there is no stored gas and there is a flame arrester, no explosion will occur.

4. Efficient

Hydrogen and oxygen flame temperature of up to 2800 degrees, concentrated flames, no heat radiation, which can achieve fast, accurate flame processing. Hydrogen and oxygen flames are carbon-free flames that do not cause secondary contamination of the workpiece.

5. Convenience

As long as there is water, electricity can be used at any time, and it is a mobile energy device.

Gas production principle: Hydrogen and oxygen welding machine uses water as the medium, and the electricity will electrochemically decompose water to produce hydrogen and oxygen. Hydrogen is used as fuel, oxygen is used for combustion, and the hydrogen and oxygen flames are used to ignite to form the hydrogen and oxygen flame, and the workpiece is welded. operation,


Feedback